TU Series | UT Series | TX Series | RP Series | EP/AP Series | CP Series
TU Series Specifications
|
TU-2 |
TU-3 |
TU-7 |
TU-11 |
TU-27 |
TU-60 |
Square Drive |
3/4" |
1" |
1 1/2" |
1 1/2" |
2 1/2" |
2 1/2" |
Minimum Torque (Ft/lbs) |
127 |
330 |
740 |
1100 |
2720 |
5800 |
Maximum Torque (Ft/lbs) |
1270 |
3330 |
7400 |
11010 |
27200 |
58000 |
Minimum Torque (Nm) |
172 |
447 |
1003 |
1491 |
3687 |
7862 |
Maximum Torque (Nm) |
1722 |
4514 |
10031 |
14925 |
36872 |
78625 |
Output Accuracy |
+/-3% |
+/-3% |
+/-3% |
+/-3% |
+/-3% |
+/-3% |
Repeatability |
100% |
100% |
100% |
100% |
100% |
100% |
Duty Cycle |
100% |
100% |
100% |
100% |
100% |
100% |
Tool Weight (lbs) |
3.9 |
9 |
19 |
29 |
70 |
130 |
Tool Weight (Kg) |
1 |
4 |
8 |
13 |
31 |
58 |
Height |
4.20"/
106.7mm |
5.30"/
134.6mm |
7.14"/
181.4mm |
7.81"/
198.4mm |
10.19"/
258.8mm |
11.50"/
292.1mm |
Length 1 |
4.82"/
122.4mm |
6.20"/
157.5mm |
8.45"/
214.6mm |
9.25"/
235.0mm |
12.32"/
312.9mm |
15.38"/
390.7mm |
Length 2 |
6.34"/
161.0mm |
8.20"/
208.3mm |
11.19"/
284.2mm |
12.25"/
311.2mm |
16.33"/
414.8mm |
20.40"/
518.2mm |
Radius |
0.98/
24.9 |
1.29/
32.8 |
1.75/
44.5 |
1.91/
48.5 |
2.46/
62.5 |
3.10/
78.7 |
Width 1 |
2.00/
50.8 |
2.63/
66.8 |
3.61/
91.7 |
3.95/
100.3 |
5.26/
133.6 |
6.58/
167.1 |
Width 2 |
2.79/
70.9 |
3.68/
93.5 |
5.06/
128.5 |
5.43/
137.9 |
7.57/
192.3 |
8.89/
225.8 |
Width 3 |
4.42/
112.3 |
5.81/
147.6 |
7.98/
202.7 |
8.72/
221.5 |
11.63/
295.4 |
14.29/
363.0 |
Back to top of page
UT Series Specifications
|
UT-2 |
UT-3 |
UT-7 |
UT-11 |
Square drive |
3/4" |
1" |
1 1/2" |
1 1/2" |
Minimum Torque(Ft/lbs) |
127 |
330 |
740 |
1100 |
Maximum Torque (Ft/lbs) |
1270 |
3330 |
7400 |
11010 |
Minimum Torque (Nm) |
172 |
447 |
1003 |
1491 |
Maximum Torque (Nm) |
1722 |
4514 |
10031 |
14925 |
Output Accuracy |
+/- 3% |
+/- 3% |
+/- 3% |
+/- 3% |
Repeatability |
100% |
100% |
100% |
100% |
Duty Cycle |
100% |
100% |
100% |
100% |
Tool Weight (lbs) |
3.9 |
9 |
19 |
29 |
Tool Weight (Kg) |
1 |
4 |
8 |
13 |
Height |
4.20 / 106.7 |
5.30 / 134.6 |
7.14 / 181.4 |
7.81 / 198.4 |
Length 1 |
4.82 / 122.4 |
6.20 / 157.5 |
8.45 / 214.6 |
9.25 / 235.0 |
Length 2 |
6.34 / 161.0 |
8.20 / 208.3 |
11.19 / 284.2 |
12.25 / 311.2 |
Radius |
0.98 / 24.9 |
1.29 / 32.8 |
1.75 / 44.5 |
1.91 / 48.5 |
Width 1 |
2.00 / 50.8 |
2.63 / 66.8 |
3.61 / 91.7 |
3.95 / 100.3 |
Width 2 |
2.79 / 70.9 |
3.68 / 93.5 |
5.06 / 128.5 |
5.43 / 137.9 |
Width 3 |
4.42 / 112.3 |
5.81 / 147.6 |
7.98 / 202.7 |
8.72 / 221.5 |
Back to top of page
TX Series Specifications
|
TX-1 |
TX-2 |
TX-4 |
TX-8 |
TX-16 |
TX-32 |
TX-45 |
Hex Range From |
5/8"/
17mm |
3/4"/
19mm |
1"/
25mm |
1 7/8"/
50mm |
2 5/8"/
65mm |
3 1/8"/
80mm |
3 1/8"/
80mm |
Hex Range To |
1 5/8"/
41mm |
2 3/8"/
60mm |
3 1/8"/
80mm |
4"/
105mm |
4 5/8"/
115mm |
6 1/8"/
155mm |
6 1/8"/
155mm |
Minimum Torque(Ft/lbs) |
45 |
192 |
395 |
830 |
1560 |
3220 |
4850 |
Maximum Torque (Ft/lbs) |
560 |
1928 |
3950 |
8630 |
16600 |
35650 |
47380 |
Minimum Torque (Nm) |
61 |
260 |
535 |
1125 |
2155 |
4365 |
6575 |
Maximum Torque (Nm) |
759 |
2614 |
5355 |
11699 |
22503 |
48327 |
64228 |
Output Accuracy |
+-3% |
+-3% |
+-3% |
+-3% |
+-3% |
+-3% |
+-3% |
Repeatability |
100% |
100% |
100% |
100% |
100% |
100% |
100% |
Duty Cycle |
100% |
100% |
100% |
100% |
100% |
100% |
100% |
Cylinder Weight (lbs) |
1 |
3.50 |
6.00 |
11.70 |
16.00 |
26.00 |
29.00 |
Cylinder Weight (Kg) |
0.45 |
1.50 |
2.70 |
5.00 |
7.30 |
11.50 |
13.00 |
Link Weight From (lbs) |
1 |
2.40 |
5.40 |
11.90 |
21.00 |
29.00 |
29.00 |
Link Weight To (lbs) |
1 |
3.50 |
7.60 |
14.50 |
28.00 |
39.50 |
39.50 |
Link Weight From (Kg) |
0.45 |
1.00 |
2.40 |
5.50 |
9.50 |
13.00 |
13.00 |
Link Weight To (Kg) |
0.45 |
1.50 |
3.40 |
6.50 |
13.00 |
17.90 |
17.90 |
Length |
4.37/
111.0 |
6.45/
163.8 |
7.87/
199.9 |
10.20/
259.1 |
12.93/
328.4 |
15.8/
401.3 |
16.75/
425.5 |
Height |
3.25/
82.6 |
4.00/
101.6 |
5.60/
142.2 |
7.00/
177.8 |
7.58/
192.5 |
9.50/
241.3 |
10.28/
261.1 |
Width |
0.78/
19.8 |
1.25/
31.8 |
1.63/
41.4 |
2.05/
52.1 |
2.50/
63.5 |
3.24/
82.3 |
4.88/
124.0 |
Radius |
0.23/
5.8 |
0.36/
9.1 |
0.46/
11.7 |
0.54/
13.7 |
0.65/
16.5 |
0.93/
23.6 |
0.93/
23.6 |
Back to top of page
RP Series Specifications
|
RAPTOR
500 |
RAPTOR
1000 |
RAPTOR 2000 |
RAPTOR
3000 |
RAPTOR
6000 |
Square Drive |
|
¾” |
|
|
|
Min. Torque (Ft/Lbs) |
120 |
250 |
450 |
740 |
|
Max. Torque (Ft/Lbs) |
500 |
1000 |
2000 |
3000 |
|
Min. Torque (Nm) |
162 |
338 |
610 |
1003 |
|
Max. Torque (Nm) |
677 |
1355 |
2711 |
4067 |
|
Dimension DA |
7.86"/
199.65mm |
7.86"/
199.65mm |
7.86"/
199.65mm |
7.89"/
200.41mm |
|
Dimension DB |
0.75"/
19.05mm |
0.75"/
19.05mm |
1.00"/
25.4mm |
1.00"/
25.4mm |
|
Dimension DC |
6.82"/
170.5mm |
7.78"/
197.62mm |
8.35"/
211.33mm |
9.99"/
253.75mm |
|
Dimension DD |
2.56"/
65.03mm |
2.62"/
66.55mm |
2.85"/
72.39mm |
3.44"/
87.38mm |
|
Weight |
9lbs/4kg |
10lbs/4.5kg |
12lbs/5.4kg |
16lbs/7.3kg |
|
Performance (RPM) |
45 |
25 |
20 |
5 |
|
Back to top of page
EP/AP Series Specifications
EP1000
|
VALVE |
MOTOR SPECS |
FLOW RATE @ 115 & 230 VAC
CUBIC IN (LITER) PER MIN. |
WEIGHT |
(Gallons) |
Control |
Type |
Permanent Magnet |
600 |
10,000 |
(lbs) |
1 |
Solenoid |
4 Way/
3 Pos. |
1.5 HP Single
Phase |
700(12) |
50(0.9) |
56 |
EP1000-Q
|
VALVE |
MOTOR SPECS |
FLOW RATE @ 115 & 230 VAC
CUBIC IN (LITER) PER MIN. |
WEIGHT |
(Gallons) |
Control |
Type |
Permanent Magnet |
600 |
10,000 |
(lbs) |
2 |
Solenoid |
4 Way/
3 Pos. |
1.5 HP Single
Phase |
700(12) |
50(0.9) |
56 |
EP500
|
VALVE |
MOTOR SPECS |
FLOW RATE @ 115 & 230 VAC
CUBIC IN (LITER) PER MIN. |
WEIGHT |
(Gallons) |
Control |
Type |
Permanent Magnet |
600 |
10,000 |
(lbs) |
1 |
Solenoid |
4 Way/
3 Pos. |
0.5 HP Single
Phase |
400(7.0) |
20(0.4) |
45 |
AP1000
|
VALVE |
MOTOR SPECS |
FLOW RATE
CUBIC IN (LITER) PER MIN. |
WEIGHT |
(Gallons) |
Control |
Type |
4 vane pneumatic |
600 |
10,000 |
(lbs) |
2 |
Solenoid |
4 Way/
3 Pos. |
1.5 HP / Vane |
700(12) |
50(0.9) |
56 |
AP1000-P
|
VALVE |
MOTOR SPECS |
FLOW RATE @ 115 & 230 VAC
CUBIC IN (LITER) PER MIN. |
WEIGHT |
(Gallons) |
Control |
Type |
Permanent Magnet |
600 |
10,000 |
(lbs) |
2.5 |
Solenoid |
4 Way/
3 Pos. |
3 HP / 4 vane |
640(11) |
60(1.0) |
52 |
Back to top of page
CP Series Specifications
TLM Series Ultrasonic Bolt Measurement
|
|
TRANSDUCER |
Size:
Width (2.5in/63.5 mm)
Height (6.5 in/165 mm)
Depth (1.24 in/31.5 mm)
Weight:
13.5 ounces (with batteries).
Keyboard:
Membrane switch pad with
twelve tactile keys.
Operating Temperature:
14 to 140F (-10C to 60C)
Case:
Extruded aluminum body with nickel-plated aluminum end caps (gasket sealed).
Data Output:
Bi-directional RS232 serial port. Windows® PC interface software.
Display:
1/8in VGA grayscale display (240 x 160 pixels). Viewable area 2.4 x 1.8in (62 x 45.7mm). EL backlit (on/off/auto).
|
Range: From 1” to 48” (25.4mm to 122cm) bolts.
Time: Nanoseconds.
Elongation: Change in length (inches/millimeters).
Load: Force load applied (pounds kIP or kN Killonewtons).
Stress: Force for unit area stress applied (pounds kPSI or megapascals MPa).
Strain %: percentage strain applied (inches per inch or millimeters per millimeter)
Resolution:
+/- .00001 inches (0.0001 mm) |
Transducer Types:
Single Element (1 to 10 MHz & 1/8” to 1” diameters).
Locking quick disconnect
“00” LEMO connectors.
Standard 10 foot cable.
Custom transducer cable lengths available on request.
Temperature probe for automatic temperature compensation.
|
ULTRASONIC SPECIFICATIONS
|
|
FEATURES |
Measurement Modes:
Pulse-Echo (standard)
Pulse-Echo w/Gate (fine adjust)
Pulser:
Square wave pulser with adjustable pulse width (spike, thin, wide).
Receiver:
Manual or Auto Set gain control with 40dB range.
Timing:
10 bit 250 MHz digitizer
|
.0492 to .3936 in/ms
1250 to 9999 meters/sec
Fixed, Single, and Two point zero calibration options.
Select bolt material types from a preset or custom list.
Units:
English & Metric / Fahrenheit & Centigrade. |
Setups:
64 custom user defined setups. Factory setups can also be edited by the user.
Gate:
Gate used to fine adjust where the detection point occurs.
Alarm Limits:
Set hi and lo tolerances with audible beeper, viewable scan bar, and visual LEDs.
Auto Set:
Locates the detection signal, optimizes the gain setting, and adjusts the overall display to show the waveform and detection point automatically.
Field Calibration:
Vector & linear regression.
Certification
Factory calibration traceable to national standards.
Warranty:
13 Month Limited
|
|
|
|
Three 1.5V alkaline or
1.2V NiCad AA cells.
Typically operates for 150 hours on alkaline and 100 hours on NiCad (charger not included.)
Auto power off if idle 5 min.
Battery status icon.
|
A-Scan:
Rectified +/- (half wave view), or RF (full waveform view).
Large Digits:
Display and toggle between nanoseconds, elongation, load, stress, and strain.
Digit Height: 0.400 in (10mm).
Limits Bar(alarm limits):
Set Hi & Lo alarm limits for displaying an acceptable tolerance range.
Repeatability Bar Graph:
Bar graph indicates stability of measurement.
Data Logger (Internal):
Total of 8,000 readings, multiple bolt groups. Stores both waveform views, nanoseconds, elongation, load, stress, and strain for each reading.
Memory:
16 megabit non-volatile ram.
|
|
Back to top of page
Industrial Impact Sockets
|
IMPERIAL (1/2" - 2 3/8") and METRIC (17mm - 60mm)
|
Available in 6 Point Standard, 6 Point Deep, 6 Point Thinwall, 6 Point Deep Thinwall, and 12 Point Configurations, as well as Hex Driver Sockets, Extensions and Adaptors
1" Drive
|
1" DRIVE |
IMPERIAL (3/4" - 4 1/2") and METRIC (19mm - 115mm) |
Available in 6 Point Standard, 6 Point Deep, 6 Point Thinwall, 6 Point Deep Thinwall, and 12 Point Configurations, as well as Hex Driver Sockets, Extensions and Adaptors |
1 1/2" DRIVE |
IMPERIAL (1 3/8" - 5 1/8") and METRIC (32mm - 130mm) |
Available in 6 Point Standard, 6 Point Deep, and 12 Point Configurations, as well as Extensions and Adaptors |
2 1/2" DRIVE |
IMPERIAL (1 5/8" - 9 1/4") and METRIC (43mm - 225mm) |
Available in 6 Point Standard and 6 Point Deep Configurations, as well as Extensions and Adaptors |
Back to top of page
TBW BackUP Wrench
|
METRIC SIZES |
PART # |
SIZE |
PART # |
SIZE |
PART # |
SIZE |
PART # |
SIZE |
BC-012 |
3/4" |
BC-200 |
2" |
BC-19M |
19mm |
BC-46M |
46mm |
BC-014 |
7/8" |
BC-203 |
2 3/16" |
BC-22M |
22mm |
BC-50M |
50mm |
BC-100 |
1" |
BC-206 |
2 3/8" |
BC-24M |
24mm |
BC-55M |
55mm |
BC-102 |
1 1/8" |
BC-209 |
2 9/16" |
BC-27M |
27mm |
BC-60M |
60mm |
BC-104 |
1 1/4" |
BC-212 |
2 3/4" |
BC-30M |
30mm |
BC-65M |
65mm |
BC-107 |
1 7/16" |
BC-215 |
2 15/16" |
BC-32M |
32mm |
BC-70M |
70mm |
BC-110 |
1 5/8" |
BC-302 |
3 1/8" |
BC-36M |
36mm |
BC-75M |
75mm |
BC-113 |
1 13/16" |
BC-41M |
41mm |
BC-80M |
80mm |
TBW-SS Set Contains wrench handle, 10 standard back-hold cartridges and carrying case |
TBW-SS Set Contains wrench handle, 10 metric back-hold cartridges and carrying case |
Back to top of page
TFS Series Flange Spreader
|
|
|
Weight of TFS-10H, Hydraulic Flange Spreader |
15.5 lbs |
7.0 Kgs |
Weight of TFS-10M, Manual Flange Spreader |
17.0 lbs |
7.7 Kgs |
Length of TFS-10H |
13.25" |
33.6mm |
Length of TFS-10M |
14" |
35.5mm |
Width of Feet |
4.5" |
114mm |
Width of Body |
4" |
101mm |
Tips Closed |
.09" |
2.3mm |
Tips Open |
3" |
76.2mm |
Tip Penetration |
1.5" |
Rated Force |
10,000 lbs |
4,535 Kgs |
Back to top of page
TN Series Nut Splitter
|
|
|
|
|
|
|
|
|
TN-100 |
1/2" - 1" |
11/16" |
10 1/4" |
30° |
1/4" |
1 1/16" |
2 7/8" |
8.2 lbs |
TN-105 |
5/8" - 1 7/16" |
1 1/2" |
10 7/16" |
60° |
3/8" |
1 1/2" |
4 1/8" |
21.6 lbs |
TN-200 |
1 7/16" - 2" |
1 1/2" |
11 5/16" |
45° |
1/2" |
2 1/8" |
4 1/4" |
22.9 lbs |
TN-205 |
1 13/16" - 2 3/8" |
2 1/4" |
15 5/32" |
30° |
9/16" |
2 1/2" |
6 7/16" |
71.5 lbs |
TN-210 |
2 1/4" - 2 3/4" |
2 1/4" |
15 11/16" |
30° |
11/16" |
2 7/8" |
6 7/16" |
72.3 lbs |
TN-310 |
2 3/4" - 3 1/2" |
3 1/16" |
18 1/8" |
30° |
3/4" |
3 7/8" |
8 7/16" |
158.66 lbs |
TN-315 |
3 1/8" - 3 7/8" |
3 1/8" |
19 7/32" |
30° |
7/8" |
4 1/4" |
8 7/16" |
163.94 lbs |
TN-405 |
3 3/4" - 4 1/4" |
3 3/4" |
22 13/16" |
60° |
1 1/8" |
4 5/8" |
9 7/8" |
251.2 lbs |
TN-500 |
4 1/2" - 5" |
TN-505 |
4 7/8" - 5 3/8" |
4 1/8" |
23 17/32" |
60° |
1 1/8" |
5 7/8" |
9 7/8" |
262.9 lbs |
Back to top of page
Turbine Tooling
|
12 Point Standard Slugging Wrenches, available from 7/8" - 7 1/2" A/F
|
SSS SERIES
|
12 Point Standard Stack Sockets, available from 3/4" - 7 1/2" A/F |
CSW SERIES |
Castellated Slugging Wrenches, available from 1 3/4" - 7" Nominal Size |
CS SERIES |
Castellated Sockets, available for 1", 1 1/2", and 2 1/2" Drives |
CSS SERIES |
Castellated Stack Sockets, available from 1 3/4" - 7" Nominal Sizes |
Back to top of page
|
